| |
All Systema
Full-tune kit includes the
following: cylinder set (cylinder
head, cylinder and piston head),
piston, spring, anti-reverse latch,
bushings and metals. Depend on the
gun, some other parts may be
included, such as selector plate,
switch assembly or even a systema
12v battery. Note that the
descriptions below are of the
general case, there may be special
cases depending on the gun.
Hi-speed:
Comes with hi-speed cylinder set,
hi-speed gears, polycarbonate piston
(zs-05-01), ball bearing and usually
M90 spring.
Super
Hi-speed: New for 1999. This set
improves up on the original hi-speed
gear set by incorporating ball
bearing bushings as part of the gear
itself, thus eliminating the need to
adjust metal shims. It also uses a
skeletonized stainless steel spur
gear. Detailed specs remains unknown
at this point. As any new product,
it needs to be tested to prove
itself. According to systema, if you
use this kit with a 12v battery,
there may be some BB feeding
problems since the whole system will
be working at a phenomena rate.
Standard:
Comes with NB (or teflon) cylinder
set, standard torque ALL Helical
Gears, polycarbonate piston
(zs-05-01), ball bearing and M100
spring.
Expert:
Comes with NB (or teflon) cylinder
set, super torque-up ALL Helical
Gears, polycarbonate piston
(zs-05-01), ball bearing and M130
spring.
Professional:
Comes with Bore-up cylinder set,
super torque-up Helical Gears,
polycarbonate piston (zs-05-02),
oilless metal bushing and M150
spring.
|
|
| |
Helical
Gear Set: The teeth that connect
the sector gear and the spur gear
are cut at an angle. This causes
less stress on any one tooth because
it has more teeth touching and
spinning is not in an outward
direction but into the gearbox.
There is one exception to the
helical gear set. You muct use a
particular piston. The bevel gear
has the teeth all the way around.
The side of the gear that allows the
piston to fire forward has one half
the side of the teeth cut. So you
have to use a piston that also has
half the side of the teeth cut. The
Helical Gear Set comes with the
piston.
All Helical
Gear Set: Has teeth cut at an
angle on all of the gears. Also the
bevel gear has the smooth side so it
can be used with the original
piston.
Flat Gear
Set: Is cut with the original
specs. These gears are made out of a
denser metal and Teflon treated like
the other gears.
High Speed
Gear: Increases the rate of
fire. Do not use a spring stiffer
than M100. This gear also gives
lower delay time between trigger
pull and fire.
Standard
Gear: Cut to original specs.
Recommended to use a M120 or less
due to the strain on the motor.
Torque Up
Gear: Designed to be used with a
M130 to M140 spring. All of the
torque up gears will slow the rate
of fire a little but reduce the
strain on the motor caused by the
gear. The greater the torque up the
slower the rate of fire.
Super
Torque Up: Designed to be used
with a M140 to M150 spring.
Ultra
Torque Up: Designed to be used
with a M150 to M160 spring.
Infinite
Torque Up: Designed to be used
with a M160 to M200 spring.
|
|
| |
Bore Up
Cylinder: Has a larger cavity,
which produces more air. Should be
used with a M140 spring or higher.
N-B
Cylinder: Nickel plated standard
size cylinder.
Teflon
Cylinder: Has a smoother inside
and is best for high speed.
Silent
Piston Head: Has a rubber bumper
on the end that makes the gun a lot
quieter when firing.
|
|
| |
Spring
Guide: The piece inside the
spring and is in the back of the
gearbox. The ones with bearings
allow the spring to spin in the back
while it is being compressed. This
keeps the spring from having any
unusual stress.
Tappet
Plate: The piece that holds the
air nozzle in place, which pushes
forward to chamber a BB round.
Metals:
The bushing between the gears and
the mech box, allow gears to rotate
with less friction.
|
|
more info
